Click to enlarge

Liquid Pressure Sensor XGZP6826A

Wide Ranges: 0kPa～100kPa…2500kPa(show in Pressure Range Example)
Optional 5V or 3.3V Power Supply
Absolute Pressure Type
For Non-corrosive Gas or Air or Liquid
Calibrated Amplified Analog Signal(Refer to XGZP6826D for I2C interface)
Temp. Compensated: 0℃～+60℃(32℉～+140℉)
Low Cost for wide application

Description
SAFETY NOTES & WARRANTY

Description

Liquid Pressure Sensor XGZP6826A

Manufacturer	CFSensor
Product Category	Pressure Sensor
Series	XGZP6826A
Model Number	As Order Guide
Pressure Range	0kPa～100kPa…2500kPa
Pressure Type	Absolute
Power Supply	5V/3.3V
Output Type	Amplified Analog
Output	0.5~4.5V/0.2~2.7V
Accuracy	±2.5%(customizable)
Measured Media	Air or Non-corrosive Gas or Liquid
Temp. Compensated	0℃～+60℃(32℉～+140℉)
Operating Temp	-30~105°C
Package	Tape&Reel

APPLICATIONS

Medical device,Massage device, Hospital beds etc,.
Consumer electronics, Inflator pump etc,.
Vacuum measurement, Industrial controls etc,.
Oil pressure, Engine control/manifold absolute pressure (MAP),etc,.

INTRODUCTION

XGZP6826A is a perfect silicon pressure sensor offering a ratiometric analog interface for reading pressure over the specified full scale pressure span.

The XGZP6826A ncorporates a silicon piezoresistive pressure sensor die and an interior Application Specific Integrated Circuit(ASIC) in a small COB package.

The XGZP6826A is fully calibrated and temperature compensated for offset, sensitivity, temperature and non-linearity, so XGZP6826A pressure sensor satisfy the prefect repeatability, linearity, stability and sensibility, which can be applied directly in medical care&health, home appliances, consumer electronic, industry, automotive and other pneumatic devices etc.

XGZP6826A pressure sensor is for high volume application at an affordable cost but perfect performance.

Customized calibrations(working voltage, output voltage, pressure range etc.) are available.

DIMENSION (Unit:mm Unspecified Tolerances:±0.1mm)

Liquid Pressure Sensor XGZP6826A DIMENSION

ORDER GUIDE

6826A ORDER GUIDE

PRESSURE RANGE EXAMPLE

6826A PRESSURE RANGE

More information about XGZP6826A, refer to Datasheet or contact CFSensor

XGZP6826A Pressure Sensor V2.7.PDF

SAFETY NOTES & WARRANTY

SAFETY NOTES

Using these sensors products may malfunction due to external interference and surges, therefore, please confirm the performance and quality in actual use. Just in case, please make a safety design on the device (fuse, circuit breaker, such as the installation of protection circuits, multiple devices, etc.), so it would not harm life, body, property, etc even a malfunction occurs. To prevent injuries and accidents, please be sure to observe the following items:

The driving current and voltage should be used below the rated value.
Please follow the terminal connection diagram for wiring. Especially for the reverse connection of the power supply, it will cause an accident due to circuit damage such as heat, smoke, fire, etc.
In order to ensure safety, especially for important uses, please be sure to consider double safety circuit configuration.
Do not apply pressure above the maximum applied pressure. In addition, please be careful not to mix foreign matter into the pressure medium. Otherwise, the sensor will be discarded, or the media will blew out and cause an accident.
Be careful when fixing the product and connecting the pressure inlet. Otherwise, accidents may occur due to sensor scattering and the blowing out of the media.
If the sensor come with sharp PIN, please be careful not to hurt your body when using it.

WARRANTY

The information in this sheet has been carefully reviewed and is believed to be accurate; however, no responsibility is assumed for inaccuracies. Furthermore, this information does not convey to the purchaser of such devices any license under the patent rights to the manufacturer. CFSensor reserves the right to make changes without further notice to any product herein.

CFSensor makes no warranty, representation or guarantee regarding the suitability of its product for any particular purpose, nor does CFSensor assume any liability arising out of the application or use of any product or circuit and specifically disclaims any and all liability, including without limitation consequential or incidental damages. Typical parameters can and do vary in different applications. All operating parameters must be validated for each customer application by customer’s technical experts. CFSensor does not convey any license under its patent rights nor the rights of others.